Top Rated in Additive Manufacturing Products

Compare the most helpful customer reviews of the best rated products in our Additive Manufacturing Products store. These products are shortlisted based on the overall star rating and the number of customer reviews received by each product in the store, and are refreshed regularly.

Top rated products in Additive Manufacturing Products

4.7 | 2,265 customer ratings
92% of the ratings are 4-stars or 5-stars
This resin is great! Compared to other resins it doesn't have a strong odor, less hazard compared to other brands (still wear gloves and clean up!) and it comes out beautiful. Though the resin is pretty sticky/syrupy compared to other
        Read more
By brian
To be fair, this is the only resin I have used, I started with it since I bought an Elegoo brand 3D printer and figured for the first few bottles I would use their brand to be safe. Since then, I have continued to buy just this resin. The color choices are great, I have used the grey, white, black, and clear red so far and they have all
        Read more
By Sage
Works fantastically and has a much more mild smell compared to the anycubic resins. I used it with the Anycubic photon and found very little post-processing necessary with most pieces. (Complex prints might need more)

To share my settings:
Layer thickness: .025mm
Exposure time: 7.5 seconds
Off time: 3.5
        Read more
By Dave
4.7 | 2,199 customer ratings
93% of the ratings are 4-stars or 5-stars
I have been printing with filament for several years now and recently picked up a resin printer for making miniatures. I bought a bottle of the Anycubic Gray because it was highly rated and in my price range. Since then, it has become one of my go-to resins.

Price
There aren't many resins on Amazon that have a lower price
        Read more
By J. Doerr
I've got about 40 hours of printing with the black resin and, so far, I prefer it over the clear green that came with the machine.

The problem I had with the green resin is that the surfaces of the model that actually touched the support always came out really "mushy". It was as if too much resin was curing around the
        Read more
By Bob Rosland
The resin works great. The prints are smooth and defect free. It works really well for D&D figurines. I am however disappointed that it is not possible to get a safety data sheet (SDS) from the manufacturer and since this is probably the most hazardous chemical I have in my home right now I won't be buying again until one is
        Read more
By Kindle Customer
4.8 | 738 customer ratings
96% of the ratings are 4-stars or 5-stars
I was looking for something to make tabletop miniatures with that wouldn't break when dropped, especially if the minis have small weak parts, like swords. I was using Elegoo, Anycubic, and Sainsmart resins in the past, and while they are all good, they were all brittle. Trying out the green Siraya, and so far, so good. It prints quickly
        Read more
By Liam Craig
This is the best resin I have used, strong but not at all brittle, low odour, fast curing--with 0.040 mm layers, I am using 4 bottom layers @ 60 seconds/ exposure, then 6 seconds/layer to produce nicely detailed, smooth prints that would put any filament printer to shame.

Reasonably priced
        Read more
By cliffyk
So this is a great value, great grey color and prints detail fantastically. The non-brittle claim on the other hand is a little unfounded. This resin will snap if you flex it very far at all or impact it sharply, it doesn't appear to be any less brittle than Elegoo or Nova3D
        Read more
By Jeff G.
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.7 | 1,438 customer ratings
94% of the ratings are 4-stars or 5-stars
Like anyone else reading this comment, I purchased almost all hatchbox PLAs. Until orange, dark blue hatchbox pla was my favorite. I am not sure if a PLA can get better than this because my prints are flawless.

Orange has absolutely no stringing and prints the smoothest surfaces so far. At 0.2mm layer height, it is so smooth,
        Read more
By Dude
First filament I ever printed with, I'm now on my third spool. This stuff prints so perfectly & is so forgiving that I ended up with unreal expectations of the whole of the 3d printing experience. After trying a dozen or so filaments of differing quality (& expense), if I could only print with one PLA filament for the rest of my
        Read more
By shewmonphoto
I've worked with about 10 different filaments from several manufacturers (including another Hatchbox filament). I've had the usual woes with adhesion of course, but for some reason this orange Hatchbox filament won't stick to my build plate (tempered glass with PEI sheet). I've tried hotter temps and ended up with a lot of stringing. I
        Read more
By Douglas Patrick Caldwell
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.7 | 1,171 customer ratings
95% of the ratings are 4-stars or 5-stars
If only I knew to buy this when I bought my 3D printer, you wouldn’t think it makes a difference since the filament just passes through it. Well I promise you it does, I immediately ran into less issues and better prints after installing this. I wish I had bought it when I bought the
        Read more
By caleb
The Capricorn tubing is supposed to print flexible filaments better because of the higher tolerance of the inside diameter of the tubing. I cant speak to that because I haven't ever tried a flexible filament. However, this tubing has a higher temperature rating than the white stuff that comes with most printers and I have noticed that it
        Read more
By Borgkube
These guys accidentality sent me 120cm of this tubing instead of 1 meter which I was very pleased about. This is my first time using capricorn tubing and I can immediately tell the difference in quality compared to what my Tevo Tornado came with. Cutter and couplings work perfectly too. The results have been nothing less than amazing and
        Read more
By Pete
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.7 | 1,164 customer ratings
92% of the ratings are 4-stars or 5-stars
Nicely marked with their sizes. And the sizes are quite accurate, and quite consistent. I measured each tip.

I measured them using gauge pins, checking which size pin would go through the hole, and which size would not. The pins come in 0.001" increments, letting you determine that the hole is bigger than XX (that pin fits
        Read more
By RedO
I've replaced the original .4mm Ender 3 Pro nozzle with one of these and I'm totally happy with it, for PLA. I don't print other
        Read more
By HighRiver ForestRun
My experience with these nozzles: At first, these nozzles seemed good but then I found that many of the nozzles have threading issues. I am not gonna ruin the internal thread of my hot end by forcing these nozzles in to work. Then, a few weeks later, I noticed on a nozzle that did thread okay, did not lay down a tried and true filament,
        Read more
By Amazon Customer
4.6 | 4,254 customer ratings
89% of the ratings are 4-stars or 5-stars
Sure it may not be called "Amazon Basics" but this filament is identical - same spool, even the Overture logo and other writing on the spool match the Amazon Basics filament line. I love this stuff, it's cheap and it works well in my Prusa MK3S and my Monoprice Maker Select
        Read more
By Grahame W.
I'm a 23 year Engineering Team Leader and side hustling Maker. You can find us on element14.com and Raising Awesome on YouTube. I was not paid or provided freebies for this review.

The PLA filament worked just as any I have used before. The specs were a little wider on the diameter, but I chalk this up to them actually being
        Read more
By S. Miller
I'm extremely impressed with the way this filament has been going through my Ender 3 Pro. Great adhesion and goes through my extruder like butter. Extruder temp 195 Bed temp
        Read more
By Nick
4.6 | 2,698 customer ratings
90% of the ratings are 4-stars or 5-stars
I am a first time 3d printer owner, and this printer came highly recommended... and I have to admit while most of the problems I have had have been simply due to my lack of experience... I was frankly shocked by the lack of support from Creality. the magnetic mat is cool, but got scratched thanks to my improperly leveling the bed, I just
        Read more
By Michael J. Crawford
As a beginner printer, the Ender 3 line is extremely popular right now. And for very good reason:

* Excellent price point puts the base model under $200 and the "pro" model under $300
* Outstanding print quality that rivals much more expensive printers
* Strong, growing community - just search Thingiverse for "ender 3
        Read more
By Kurtis Miller
I am completely pleased with this printer and don't see spending more money would add any value or improve prints, all around excellent.

Product arrived perfectly, excellent packaging, all parts included, no hardware issues.

This is my first 3D printer so I want anyone new to 3D printing to have a realistic
        Read more
By photonashville
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.6 | 2,118 customer ratings
91% of the ratings are 4-stars or 5-stars
Surprised with the negative reviews on this PLA. I use Hatchbox EXCLUSIVELY and have done so for 2 years. I print cosplay props and armored suits for a living and there is NO SUBSTITUTE for this stuff in this price range. Having tried many brands I settled on Hatch along time ago. That said, I can go through up to 4-6 spools of Hatchbox
        Read more
By Amazon Customer
I am new to 3D Printing so it was pretty much sheer dumb-luck that landed this filament into my cart and then lap. I assembled my Ender 3 Pro over the course of a couple evenings, and by the weekend I was ready to start making figures and terrain. I read up on the slicer, plugged in the figures for both the printer and the PLA, took a
        Read more
By Joseph K
Okay. So I'm actually a pretty big fan of Hatchbox. I've used their black, copper, orange, red, and a few other colored PLA filaments. I've also used ZIRO's marble filament and 3d Solutech's clear filament.

But...their gray is by far the worst PLA I've ever used. Full stop. I've tried 3 rolls of this, and all 3 rolls have been
        Read more
By P and A Alter
4.6 | 2,040 customer ratings
92% of the ratings are 4-stars or 5-stars
I ordered the Elegoo Mars around the first of the year. My experience has been positive overall. The support is very good, and I found that using the facebook Elegoo Mars group is very helpful as well. Some pros and cons:
Pros:
-Very easy to set-up and use (software is relatively simple to use). Far fewer settings to adjust vs
        Read more
By Scott Presbrey
I could only print half of the test object and it failed. Maybe its user error on my part but t seems like it should be able to pring the test that came with the usb, which took 12 hours, should have been something smaller and faster, I will update when the second attempt is done.

Edit#1: After emailing the company I was
        Read more
By Amazon Customer
Coming from ZERO, 3D modeling skills. Now one week later. I can do basic modeling, and proficient knowledge in using slicer software and mesh softwares...

This machine was my entry point into the world of 3D printing. With years of window shopping for printers, I simply could not resist to take a look at this printer and jumped
        Read more
By J. Pham
4.6 | 1,316 customer ratings
92% of the ratings are 4-stars or 5-stars
This is a reluctant review because I don't want anyone to know how great this stuff is for the price. Every time I find a great resin, the price goes up astronomically. I have been consistently printing on my Anycubic Photon at settings of Layer thickness .05, Exposure of 11 seconds 1 second off time, 5 bottom layers at 95 seconds. I
        Read more
By Dr D.
The manufacturer recommends shorter curing times for this resin, but I ran the Resin XP test and found that 15 seconds with 0.05mm layers worked best. I use 15 second regular layers, 5 seconds of off time, and 10 bottom layers with 60 seconds of exposure. I’m getting consistent successful prints. Chess pieces come out with a
        Read more
By Scott Campbell
The bottle came packaged in a tight fitting air cushion inside a double walled box. No leaks unlike some other brands i have used. Cure times are virtually the same as wanhao and anycubic fast resins. Bed adhesion has been flawless and there's been no failed prints so far. The image i posted shows the clear with some pigments added to
        Read more
By bootdsc
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.6 | 1,292 customer ratings
91% of the ratings are 4-stars or 5-stars
I'm fairly new to 3D printing and was getting a bit discouraged with my results. I decided to give the Creality Ender 3 Glass Bed a try to see if it would help. It was a few dollars more than a few others I looked at, but it did not look like it was just a piece of cut glass that I could cut myself and it's not. The "microporous coating"
        Read more
By DPeter2101
My Ender 3 Pro came with the magnetic print surface a lot of people online are making a fuss about. No more having to use a scraper to get your print off the bed. Just remove it, flex it and peel off the print! Magic! Yeah, for the first 20-30 prints. Then, I noticed that there were creases in the sheet that would not self level. Printing
        Read more
By G. Martin
I am printing with PLA, and after the first couple days of printing on the 'sticky' side that has the printed dot pattern, I started running into problems with my prints not sticking properly. I had corners peeling up and small details were just not adhering well. It would take 2-3 starts before I could get a print to stick 'sort of'
        Read more
By Paul
4.6 | 970 customer ratings
89% of the ratings are 4-stars or 5-stars
So I've been printing for a while, with a bunch of different resins and this one is the most interesting. I found that while the models are water washable, the resin vat is not. I still had to use IPA to clean it adequately.

On to the models, so this resin works excellent! That is if you aren't printing anything too thin. I've
        Read more
By MoldyHacker
Yeah, it really does wash clean with water! No problems with the recommended settings on an Elegoo Mars. A little more expensive, but you save some $ on cleaning solution, so it might even
        Read more
By T. Spears
I'll admit I am new to resin printing so, take this as a new user speaking.
First off, anyone else notice this stuff fluoresces under curing lamps?... (Kinda cool.)

I REALLY like the fact I don't have to have tubs of alcohol laying around.
Odor is far less than the "normal" resin as well.
Both HUGE pluses in my
        Read more
By Kilroy07
4.6 | 957 customer ratings
91% of the ratings are 4-stars or 5-stars
There’s a little learning curve on setting up this 3d printer, for example leveling the bed otherwise you just need a little or not at all experience assembling kits. Under an hour you can have this puppy ready to print and without upgrades this printer exceeds expectations ! Now when you use Creality 3d software or Cura read 1st or
        Read more
By 3d Creations FL
*****Edited ***** I am now rating the ender 3 pro to 5 stars finished 151 hour and 47minute T-800 skull 300% size (one and a half spools of hatchbox pla) printed flawlessly. See pics. It's all in the proper set up.
This is my second 3d printer I'm a rookie I'll admit that, my 1st printer is a monoprice select mini v2 not a problem
        Read more
By shotgun_fetus
Pro: Amazon Prime got it to me a day early.
Con: Extruder's stepper motor did not work out of the box. Send Creality an email to try and see if they would like a chance to get it to work. 3 days after i sent the email ( 2 business days ) I finally got a reply to which they wanted my payment info and to confirm that I purchased it (
        Read more
By Cj
4.7 | 468 customer ratings
95% of the ratings are 4-stars or 5-stars
I have been resin printing for about a year and a half. In that time, I have tried my fair share of DIY washing and curing setups. From multiple jars of IPA to UV Lights glued onto containers, or just leaving prints outside in the sun, I’ve tried it all.

I recently learned of Anycubic’s Wash and Cure station and decided to
        Read more
By Kody D. Belshe
I expected this device to be a positive improvement for my 3d printing, but I hadn't anticipated the kind of difference it would make.

Like most people I saw this device, thought "Eh, kind of interesting, but it just does things I already have a set up for." Eventually though I was convinced to take a chance on it (being stuck
        Read more
By Kevin Waterman
I bought a Photon S a while ago and been very happy with the overall quality of it. Was excited when i saw they had came out with a all-in-one wash and curing station. So far i have not been disappointing. Great quality as expected.
my set up before i had to have different stations one for cleaning and one for curing. With this set
        Read more
By T L Computers 505
4.6 | 842 customer ratings
90% of the ratings are 4-stars or 5-stars
I've been using Overture PETG and I've been very happy with my results. I needed some white PLA, and when I read a review that said that Overture PLA didn't stick, I had to see if that was the case of if it's just another case of bad bed cleaning and a poor approach to 3d Printing that might be the cause.

So I ordered a role of
        Read more
By GasPath
Just received my first roll of Overture PLA+. I hoped for the Space Gray but got black (see below). Regardless, I decided to proceed with printing and testing of the accuracy / temperature range. The first print I did was the Benchy Boat. I printed at 205c, 60mm/s, 0.2mm layer height, 60c bed, with a 20-line brim (to help with
        Read more
By Ashley C.
This is decent filament but isn't anything special and is very overpriced. Print quality is similar to ordinary Overture PLA and overhangs and details aren't any better. This is in contrast to some other PLA+ brands that offer superior print quality and colors. I cannot speak to the improved impact resistance that Overture claims as I
        Read more
By redraider72
4.5 | 3,216 customer ratings
89% of the ratings are 4-stars or 5-stars
I purchased this printer a few months ago. It has been a dream to use. I would definitely recommend this as a great printer for anyone starting out with 3D printing or even for veterans that want a more compact and reliable unit. I am extremely impressed.

Setup
The setup was fairly straight forward. It took me about an
        Read more
By Ben
My printer's bed came severely warped. Warped enough that I could not print anything. I contacted Comgrow and they were nice enough to immediately ship me a new bed! After the new bed was installed, it printed like a dream! The only experience I've had with FDM printers is the makerbot replicator 4 and it was a nightmare to use. This
        Read more
By Defluo
You might be able to assemble this printer in a couple of hours but you can't build it in that time. There is a significant difference in building something correctly and assembling it. Assembly is the easy part, anyone can throw things together. The build is now complete and to do it correctly takes 4 to 5 hours.

When you
        Read more
By Roger T. Moore
product price FREE Shipping
Get free shipping
Free 5-8 day shipping within the U.S. when you order $25.00 of eligible items sold or fulfilled by Amazon.
Or get 4-5 business-day shipping on this item for $5.99 . (Prices may vary for AK and HI.)
Learn more about free shipping
on orders over $25.00 shipped by Amazon or get Fast, Free Shipping with Amazon Prime
4.5 | 3,119 customer ratings
88% of the ratings are 4-stars or 5-stars
This was a great set of sample colors to go with my new 3D Pen. THere's enough variety to make some interesting objects without running out. But, once you have a palette of colors you like to use, it probably makes more sense to buy larger spools of those colors. I'm almost out of the silver and the blue. I love that there were
        Read more
By Linzart
Nice selection of colors in good sample lengths. Some of the colors I haven't seen in any other assortments (and I buy A LOT of assortments): the "metal bronze" is more of a metallic goldish green, almost metallic chartreuse, and the six transparent colors are very light, perfect for subtle jewels, vehicle lights, etc. None of
        Read more
By Aldo Ross
We purchased this to accompany the 3D pen that we purchased for our daughter. This kit comes with a wide array of colors and a very generous amount of each one. The price was right and each filament has fit perfectly in the 3D pen we purchased. Be sure to check the mm size of filament that your 3D pen uses to make sure it is
        Read more
By MrsManders
4.5 | 3,011 customer ratings
86% of the ratings are 4-stars or 5-stars
MIKA3D Silk Shiny PLA 3D Printer Filament Bundle: Orange, Yellow, Lime Green
MIKA3D Silk Shiny PLA 3D Printer Filament Bundle: Champagne Gold, Pink, Pearl White
MIKA3D Silk Shiny PLA 3D Printer Filament Bundle: Pearl White, Ruby Red, Sapphire Blue
MIKA3D Silk Shiny PLA 3D Printer Filament Bundle: Emerald Green, Pearl White,
        Read more
By Ana Mardoll
So I was originally going to give this 1 star due to constant jamming of my extruder with only this filament. However, after extensive testing I have gotten the settings dialed in to the point where I no longer have issues printing. I am using an original Prusa i3 Mk3 w/ 0.4mm nozzle and have to use the following settings in order to keep
        Read more
By James
Be sure to READ the title and don't get confused by the pictures, these are mini spools of 500 grams each, so you're getting 3 500g or 1.1lbs spools, a "traditional" spool is 1 kg or 2.2lbs and larger in size. Which you can get for $10-20 a spool of PLA, so unless you need these three colors you can find better deals elsewhere on
        Read more
By David Clunie
4.5 | 2,333 customer ratings
86% of the ratings are 4-stars or 5-stars
Wow, what a wonderful filament. First buy from this company, and I’m now a customer for life. Prints came out absolutely gorgeous with only a slightly higher temp than expected. Used on an Ender 3, 205c at the nozzle and 55c on a glass bed. I had 0 issues with layer adhesion, and it’s a pretty strong filament. Was worried about
        Read more
By BlackWolfe Technologies
First - folks have asked if there is metal (or even gold) mixed in the filament. No. (At $22 a roll, really?)
It was very well sealed in a thick bag with all air removed. The bag is not reusable. They also included about 2-3 meter long samples of all of their "Silk" filaments and some nozzle cleaners. There is also an included
        Read more
By OldGeek
I was looking for a PLA that would give me a good "metallic" finish and I believe I've found it! I had been using Rust-Oleum's Metallic Gold to prime and paint my prints, but after using this PLA I don't have to do that anymore! This silk PLA catches the light nicely for a true metallic look. I'll definitely be trying their "Silver" next.
        Read more
By Amazon Customer