Top Rated in Pipe Fittings

Compare the most helpful customer reviews of the best rated products in our Pipe Fittings store. These products are shortlisted based on the overall star rating and the number of customer reviews received by each product in the store, and are refreshed regularly.

Top rated products in Pipe Fittings

4.8 | 599 customer ratings
97% of the ratings are 4-stars or 5-stars
Easy and simple to install, allows for errors to be fixed. As permanent as you'd like it to me.
We ran water lines from one part of the basement to another, since we decided to build an additional bathroom. we were fearful about cutting into the old copper tubing and attaching a new CPVC or sharkbite pipe.
After careful
        Read more
By Sisu Vesimchu
over the year I have had my camper I have heard Great things About these little jewels I say that because they must think they are made of gold but I have used slip lock connectors before on air lines and other things on autos and trucks and love the ease of use to the push on and done so when it came time for my first upgrade of adding
        Read more
By Jeremy Wilson
Ive ordered many of these. This past winter when we had the polar vortex many of our pipe joints started to drip- they're old copper pipes and I think the soldering was damaged by the extreme cold. So I've been slowly replacing the worst ones first. They are easy to use but you MUST know how to do them. And you cannot use a hacksaw
        Read more
By Kindle Customer
4.8 | 303 customer ratings
95% of the ratings are 4-stars or 5-stars
Well made and perfect for my DeWalt 30-gal air compressor. This allowed me to attach my quick-disconnect air coupler at a 90-degree angle. Now the air hose hangs straight down, relieving pressure on the
        Read more
By A. Garcia
I plumbed a braided flex hose to the drain of my air compressor and used one of these to plumb to the compressor tank and one to turn down the end of the drain hose at a shutoff valve. Wanted to make sure the hose didn't spray straight out when I open the drain. I cracked the original 90 degree fitting that came with the flex hose. These
        Read more
By Amazon user for life!
First off, these are not NPT compliant. (National Pipe Thread, the standard used in the United States). There is no taper whatsoever, the diameter is the same the entire length of the thread, which will cause the fitting to leak. Brass fittings are intended to deform and thus create a tighter connection, which is absolutely vital if you
        Read more
By Brandon
4.7 | 613 customer ratings
92% of the ratings are 4-stars or 5-stars
Picked this up to use with my new Camp Chef stove. I changed the hose to a longer length with a quick connect. Had to use This Anderson Fitting to connect the original Camp Chef hose and regulator to a new matching Quick Connect.
To Convert the Original camp Chef hoes and regular so it can connect to the 12' hose so it can still
        Read more
By Kadien
Fit perfectly on my MasterCool Vacuum pump. I was looking to improve my vacuum times, I recently purchased a Yellow Jacket vacuum pump tree that had a 1/2" connection. The original connection was 5/16" and 1/4", which wouldn't work. This connection worked flawlessly, I tested it last night on a 30lb recovery bottle. I was
        Read more
By Wingnut
Anderson Metals Brass Tube Fitting, Half-Union, 3/8" Flare x 3/8" Male Pipe
Arrived in good condition, as advertised, no problems with installation.
would purchase again.

I do not know the seller and did not receive any money or product for my review
190221
        Read more
By Runion
4.8 | 247 customer ratings
96% of the ratings are 4-stars or 5-stars
I am in the process of converting my home plumbing from CPVC to Pex. I used these T-connectors to patch into the existing plumbing to feed the new manifold. Installation is quick and leak-free. Be sure to use the Sharkbite trimming tool to clean up the edges of the CPVC (or copper or Pex). With the trimming tool in position, be sure to
        Read more
By Ward Wagher
Easy to use. Push HDPE, PEX, or copper tubing in to the required depth, and you're set. Just go ahead and buy the removal tool while you're at it. Might not need it this job, but maybe the next. Depth gauge would be nice to have, but certainly not necessary to make a leak free
        Read more
By Phil R.
I bought a home with faulty (class action lawsuit) quest plumbing. Consequently, I am no longer surprised when I find a leak in the basement. I can replace fixtures and fix commodes, but I'm no plumber. Remember Tinker toys? That's how these work. Just cut the old, leaking pvc out, maybe splice another in, snap them together with
        Read more
By Dale S.
4.7 | 524 customer ratings
93% of the ratings are 4-stars or 5-stars
The Pipe came perfectly packaged, affordable and in a timely manor. I am so happy with this product. The only thing you need to know is when crafting, do not pre-drill holes. the pipe and fixtures are slightly smaller then those of "Everflow" that you can pick up at your local hardware store or plumbing store. So hold off until you
        Read more
By James Panto
Like most people, I purchased these to build a piece of furniture and was very happy with them. They're exactly the same as what you'd buy in the plumbing section of Home Depot, but less expensive. All black pipes have a greasy coating on them upon purchase that will rub off and mark surfaces, but the coating on these seemed a bit lighter
        Read more
By David Stivelman
I made a free-standing 4 shelf unit for my weight equipment...and some of my wife's collectables. Good and sturdy without even bracing it to the wall. To do that, just put a 3\16" spacer under the lowest post at the front to give it a slight tilt. Keep the lowest shelf 1" away from the wall. Set each higher shelf 3/8" closer to the wall.
        Read more
By Mike Damiani
4.7 | 479 customer ratings
92% of the ratings are 4-stars or 5-stars
I have no clue why I bought this or where I put
        Read more
By Amazon Customer
I bought this to replace the piece of junk "1/2 to1/4 Anderson Metals Brass Threaded Pipe Fitting" that I ordered a week ago for $5.68. What a drastic difference with this NIGO 1/2 to 1/4 bushing for $5.89!!! This NIGO bushing is high quality with every part of it beautifully machined and perfect threads. The brass has a hefty feel to
        Read more
By Frank A
Good quality material nice and heavy feeling like it should be. Torqued the ffittings pretty tight no leaks. Please click helpful if this was of any help
        Read more
By Fc3sluis
4.8 | 230 customer ratings
97% of the ratings are 4-stars or 5-stars
I used it ti make an extinction from my gas valve to my new gas dryer and it worked just
        Read more
By Sphinx
Great product! Other competing products are to thin and light weight and too short for hoses to fit. This one is hefty, solid and well polished. I also am nursing numerous cuts because threads from the competitors are razor sharp and not at all polished or rolled. —Hands were cut badly after handling competitors
        Read more
By SP
I purchased 6 of these for my main water line rebuild inside the house. I had no issues; each fitting was machined well. Properly sealed with pipe joint compound, they did not
        Read more
By Dewey Bumstead
4.7 | 392 customer ratings
92% of the ratings are 4-stars or 5-stars
Over that past year I have ordered and used many different Anderson fittings. This is one of them. Without exception, I have found Anderson fittings to be top quality. No fitting has ever failed me. The threads have all been excellently cut and are well within specification for NPT design. When wrapped with PTFE and tightened properly
        Read more
By TolkienFan
just what I
        Read more
By BWSWELD
I made the mistake of assuming the "1/4 inch barb" would fit a 1/4 inch KORAM brand plastic irrigation line, but that is not true. The "1/4 inch" KORAM tube is 0.25" OD and 0.167" ID. This part's hose barb OD starts at 0.257" and the barb ridge goes up to 0.290" OD. That plastic hose cannot be stretched to
        Read more
By Amazon Customer
4.8 | 204 customer ratings
96% of the ratings are 4-stars or 5-stars
I purchased this to run an oil pressure and temperature sensor on my car. I loved the size of it and it threaded right into the fitting. My sensors threaded beautifully into it and as I've been checking I've had not leaks. It's rated for 1,000 PSI so I'm not concerned about that. The fitting does have a 250 F degree max rating and
        Read more
By Glenn Rossney
Wanted to use for a stock and aftermarket oil pressure sensor, but my front differential was in the way, as I have a 4x4. It is made of good quality, so a for
        Read more
By Dylan
I used this NIGO "T" in my air supply line running to a Laser Engraver and was impressed by the quality of the fitting and the fact that the fitting has hex surfaces making it easier to apply wrenches during installation. I had no
        Read more
By Richard R
4.7 | 354 customer ratings
94% of the ratings are 4-stars or 5-stars
Used to make flag mounts for my 1931 Model A Ford pickup. Cut it in half to make two six inch flag holders for American flags on 3/8" wooden dowels which fit perfectly inside this pipe. For those like me who are not well versed in pipe standards the actual inside diameter of this pipe is 3/8". What the 1/4" actually stands for, I have
        Read more
By ranchdog
Quick delivery and good price for brass pipe. Seems to be well made. I will update review if I have any issues with material quality in the future (i. e. Premature
        Read more
By Not Steven
Threads aren’t correct, it threads only a portion of the way in on either side, I spend more money and got a shorter chrome plated nipple and threaded the pipe all the way into the tub spout and elbow, I just added enough Teflon tape to seal it at halfway... in short, this product wouldn’t have worked despite the fact I measured
        Read more
By Roger N.
4.7 | 279 customer ratings
94% of the ratings are 4-stars or 5-stars
This product was exactly what I expected and so far looks awesome! Most important note is that the pipes are 8" INCLUDING the threads. As other reviews state, the pipes come covered in grease. They are heavy. They are grayish, not black. The pipe shaft is extremely smooth but the threads have burrs, so be careful while cleaning. Speaking
        Read more
By Elle Michele
This was our first pipe furniture project. We we working on a very large desk with a return. I did all the calculations and then started ordering all the pipe and fixtures I needed. Since we were new at this, I didn't know who to order from. We received some terrible pieces from GOOVI. They were thin, and covered in black almost
        Read more
By Knoxwell
Many issues, including:

1. Pipes were damaged, with sharp gouges in their sides that could cut the skin.

2. Covered in a layer of oil and dirt that could not be removed.

3. Not one color - came in a mix of two different colors: black and unfinished steel.

I assume the idea behind PipeDecor is
        Read more
By Arch Stanton
4.7 | 256 customer ratings
94% of the ratings are 4-stars or 5-stars
I used a couple of these to plug the test port holes in my sprinkler system vacuum breaker when the test valves began leaking. They worked as expected.

Pros:
- True 1/8" MNPT.
- Very smooth surface and threads.
- Withstood application of Teflon tape and standard tightening with an allen wrench without any
        Read more
By R. Knowlton
I installed an air separator in my heating system, and needed to plug the expansion tank fitting on the bottom of it. Because it was brass, I wanted to use the same material. (I know I didn't have to.) The counter sunk hex socket means there is nothing to catch on. I wanted this because the plug site even with the bottom of the floor
        Read more
By Mikkel
Very bad experience. The indented hex slot for tighten or remove the nut coupled with the soft brass would cause it to deform and expanded out making removing impossible. I tried to use a hex key as tight as possible to the socket, I still can't get it out. It just strips. Now, I have to try to drill right in the middle and tap it
        Read more
By T. Don
4.6 | 618 customer ratings
89% of the ratings are 4-stars or 5-stars
For whatever reason I can't find this item in any box store. When hooking up a natural gas quick connect for my grill stub-out, the quick connect had a 3/8" connection, but the gas pipe was 1/2". This worked beautifully and has held up well to the
        Read more
By matt151617
I needed to reduce a 1/2" npt to 1/4" npt quick connect fitting, this worked great...

I was plumbing in a quick connect connector into my existing lp tank line and needed a reducer.

Overall, I am happy with my
        Read more
By ChuckleHead
I got the "Anderson Metals Brass Pipe Fitting, Reducing Hex Nipple, 1/2" Male Pipe x 1/4" Male Pipe" size to try and fit my Paasche compressor, as it's fitting had a defect and finally blew out on me. This item arrived and the 1/2 inch side has a 5/8 inch INNER diameter. The outer diameter is therefore larger, because, you know, physics.
        Read more
By N. Young
4.6 | 614 customer ratings
91% of the ratings are 4-stars or 5-stars
I used these fittings on the pump and filter of my above ground pool. I used 1 1/2 inch braided vinyl tubing with stainless steel hose clamps . These fittings worked very well, and are extremely high quality. They put to shame the more expensive gargage fittiings that you find at Home Depot and
        Read more
By Drayton Sawyer
Used to hook up a pool filter with a 1.5” hose. Worked great, no leaks, just wrapped some Teflon tape on the threads. The barbed end sealed up nicely on the hose with a stainless hose clamp. Arrived in two days, price was better or competitive with anything I could get locally without having to drive to several different stores
        Read more
By DTSully
Not exactly as pictured, I was looking for 3/4 to 3/4. This is 3/4 to half inch. You can see the actual picture of the product is different than what is pictured on product info. If you're looking for 3/4 to 1/2 inch it's a fine product, but that wasn't what I
        Read more
By Randy Smith
4.6 | 574 customer ratings
92% of the ratings are 4-stars or 5-stars
I used this fitting for my Weber Q 1000. Everything work out
        Read more
By Frank Contreras
I purchased a propane quick connect hose, and then discovered I could not connect to a LPG generator from a 5th Wheel quick connect outlet. This double female coupling allowed me to make the connection. I removed the safety quick connect valve, installed the coupling, and attached a 1/4 inch male quick connection, which I inserted into
        Read more
By James Barr
The 1/4" is the inside hole diameter. The outside diameter is about 3/8". The threads on one end got a little smashed and threading the pipe on it was a challenge but I got it to fit since brass is soft enough to work with so long as you don't cross thread
        Read more
By Glittergal
4.8 | 136 customer ratings
95% of the ratings are 4-stars or 5-stars
Good quality. Will be purchasing more tubes and fittings from this vendor. Very heavy gauge 304 stainless steel. If you need this don't hesitate to purchase this. You won't be
        Read more
By Nathan
It works as it should. It came packaged very good. I had no issues with it at all. It works like a
        Read more
By Reed Dawg
By Lyndon Gash
4.6 | 381 customer ratings
89% of the ratings are 4-stars or 5-stars
Just as expected. Wording in the text is wrong. This is (as seen from the picture) 3/4 inch male hose thread to 1/2 inch NPT female thread. Other reviewers have pointed this out. Amazon's technical writers might want to take heed and fix the
        Read more
By Mark Gugel
Why would you need to attach a GARDEN HOSE to your SHOWER instead of an actual shower head??

Because, it's none of your business! J/K... I'm doing this because I need to fill my giant portable swamp cooler every day and I don't want to have to roll this giant thing outside to the hose, and then back inside (heavy, awkward,
        Read more
By MuchosPoptartos
Finally found the right adapter! Wanted to hook up a drinking-safe water garden hose to fill a fish tank. Works
        Read more
By DDR1981
4.6 | 341 customer ratings
92% of the ratings are 4-stars or 5-stars
Joe's Winterization Tool was assembled from... This small but important item 5) and 4 other items...
1. Air Compressor Quick-Connect Plug To Male Garden Hose Faucet Blow Out Adapter with Valve
2. Neiko 30252A Water and Oil Separator for Air Line with ¼” NPT Inlet and Outlet
3. Camco 36003 Hand Pump Kit
4. Bostitch
        Read more
By Joeman
After being burned twice in a row by inexpensive imported fittings bought through Amazon.com, I found this brand which ARE within specs. Male threads are cut correctly, not undersized like the imported ones I tried, so they seal up well before bottoming out. I'll gladly pay more for fittings I can trust and these Anderson fittings are the
        Read more
By David Anderson
The product described on the Amazon.com website is a "nipple for connecting two threaded pipes" and the picture shows a brass fitting that is threaded at both ends. Even though the fitting received has the same product number (56122), it is nothing like that pictured or described (it is only threaded on one end). Because this item cost
        Read more
By Snoopy1
4.7 | 183 customer ratings
93% of the ratings are 4-stars or 5-stars
These things are super useful for any pvc application where you have a threaded attachment that you might want to unthread at some point. If everything is glued together, you can't turn it to unthread it! I used these to put a break in a line running from a water barrel. They attach to your pipe just like any other glued joint but then
        Read more
By Seth Dingwell
If you replace your broken sprinkler valve, install this union. You will never need to cut and glue the pipe again. I wish it were default installation for the sprinkler valves. Since sprinkler valve usually fails after some number of years, with this union installed, replacement becomes so easy. I've bought three and used two. They work
        Read more
By Shan J.
I have recently installed a whole-house filter system. One union on the input and another on the output allows me to disconnect if I have to. ( Rather than cutting
        Read more
By Stanley Cooper
4.7 | 179 customer ratings
95% of the ratings are 4-stars or 5-stars
I really like Anderson's brass fittings.... And this one is certainly one of the best.

This barstock tee is extremely strong and well made. I found the threads to be well formed and well within the "standard" for size. They felt extremely "smooth" going together and all appropriately sized fittings mated up perfectly without
        Read more
By TolkienFan
I agree with other reviewers who have stated that the picture is not accurate. The fitting is turned down to a round pipe-like end on all three arms of the T - unlike what the picture shows. I deducted one star from the review for the inaccurate and misleading picture. In terms of functionality, in most cases this will not affect the use
        Read more
By Charles W.
Good quality, except it had a minuscule thread defect, I’d have guessed the threading operation stopped and restarted because there was a line following the contour of the threads in one hole. Doesn’t leak so I’ll rate it high. Has somewhat of a banged up finish, minor dings and dents, none larger than a sixteenth of an inch wide
        Read more
By H. Stewart